Plumbing Basics: Your Key to Bathtub Installation
Plumbing Basics: Your Key to Bathtub Installation
Blog Article
They are making several good annotation on How to Install a Bathtub Yourself in general in this post down below.
Installing a tub isn't precisely brain surgery, however it does need solid plumbing, carpentry, as well as often, tiling skills. Replacing an old bathtub with a new one is likewise a moderately challenging project. If the old bathtub is easily obtainable, the task can move rapidly; if you need to open up a wall to get rid of the old tub as well as position the new tub, the job is much harder. In either instance, the task is within a home handyman's skills, although you will need a helper to move out the old bathtub as well as embeded in the brand-new one. Make sure you have certified on your own for the task and also fit attempting it. Instead of working with a professional to take over a halfway-completed project, it is better to consider using one before you start. Possibilities are you may require a professional plumber to make tube connections.
This article will help you mount a brand-new bathtub in your shower room if you have actually already bought a brand-new tub and also do not require to alter the arrangement of your previous water supply pipes.
Your tools as well as material checklist must comprise the following:
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installment, then the first thing you need to do is detach the water supply. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of removing the existing taps can be fairly problematic because of the limited access that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the faucets. Have a cloth prepared for the staying water that will certainly come from the pipelines. When the supply pipelines have been removed, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming during this process. Once the faucets have been eliminated, the holes in the bath/basin will have to be cleaned of any old securing compound.
Prior to carrying on to fit the brand-new taps, compare the pipeline connections on the old taps to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.
Fitting New Touches
If the tails of the new taps are plastic, after that you will need a plastic adapter to stop damages to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end provides a connection to the current supply pipes.
If you need to fit a monobloc, after that you will certainly need lowering couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the placing hole in the bath/basin guaranteeing that the washers remain in area between the faucet and the sink. Secure the tap in position with the manufacturer supplied backnut. When the faucet is firmly in position, the supply pipes can be attached to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap ports. The previous kind ought to be linked to the tap ends first, tightening up just by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Bath tub
Using both wooden boards under its feet, position the tub in the required setting. The wooden boards are handy in evenly spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four small factors.
The following objective is to make certain that the bathtub is leveled all round. This can be attained by inspecting the level as well as readjusting the feet on the bathtub up until the level reviews degree.
To set up faucets, fit the bottom of the outermost versatile tap port to the ideal supply pipeline by making a compression join; after that do the same for the various other tap.
Activate the water system and inspect all joints as well as new pipework for leakages as well as tighten them if needed. Fill the bathtub and additionally check the overflow electrical outlet as well as the typical outlet for leakages.
Finally, repair the bathroom paneling as defined in the maker's instruction manual. Tiling and also securing around the bathtub must wait till the bath tub has actually been used at least once as this will certainly resolve it into its last placement.
Getting ready for the Installation
First of all, the supporting framework provided with the bath should be fitted (if needed) according to the maker's instructions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is essential to ensure that if the faucet comes with a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps system to prevent pressure on the bathtub.
Fit the flexible tap connectors to the bottom of both taps making use of 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet with the hole in the bath. Make use of the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. See to it you make use of all of the provided washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom need to now prepare to be fitted in its last setting.
Tiling Around the Bath tub
In the area where the bath satisfies the tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to break an inflexible seal, causing the water to pass through the wall surface in between the bath and the tiling, causing complications with wetness and also possible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to blend in your fixtures as well as installations. They are offered in tubes and cartridges, as well as can securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with spins of soaked paper or soft rope. Bear in mind to always fill up the tub with water prior to securing, to allow for the activity experienced when the bathtub remains in usage. The sealant can fracture relatively early if you do not think about this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise quickly readily available on the marketplace. It is advisable to fit the tiles utilizing water-resistant or waterproof adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy more info about How to Install a Bathtub Yourself? Write feedback directly below. We will be pleased to know your ideas about this post. We hope that you visit us again in the near future. Are you aware of someone else who is looking into the subject? Be sure promote it. Many thanks for your time. Come back soon.
Urgent support required? Report this page